As power consumption in some high-density AI server racks exceeds 100 kW, cold-plate liquid cooling is increasingly important for managing heat from CPUs, GPUs, and other high-performance components. Coolant flows through distribution manifolds and pipes into cooling plates, transferring heat away from electronic components.
Welded joints throughout the cooling circuit must withstand internal pressure and repeated temperature changes. Even a small welding defect can cause coolant leakage, potentially affecting system reliability and increasing maintenance costs. For high-volume manufacturing, consistent weld quality must be supported by in-process monitoring and post-weld leak testing.
Han’s Laser provides laser welding equipment and automated production solutions for liquid cooling plates, manifolds, corrugated tubes, and related components, combining specialized laser sources, process monitoring, and automated handling to support reliable production.
Key Welding Challenges in Liquid Cooling Manufacturing
1.Welding High-Reflectivity Copper
Copper is widely used in liquid cooling plates because of its high thermal conductivity. However, copper absorbs relatively little 1064 nm infrared laser energy at room temperature, making initial energy coupling and stable keyhole formation more challenging. Unstable welding conditions can lead to spatter, porosity, or incomplete fusion.
2.Joining Dissimilar Materials
Some liquid cooling assemblies combine copper with stainless steel to balance thermal performance and structural requirements. Differences in melting temperature, thermal conductivity, and thermal expansion complicate joint formation and narrow the process window. Laser power distribution, heat input, joint preparation, and welding speed must be carefully controlled.
3.Maintaining Consistency in Mass Production
Cooling plate channel closures, manifold connections, and tube joints require repeatable weld quality. Local defects can compromise leak tightness, making process stability, defect detection, and production traceability essential for large-scale manufacturing.

Comparing Three Welding Processes for Liquid Cooling Plates
The appropriate joining process depends on the cooling plate design, joint geometry, production volume, and performance requirements.

| Process | Advantages | Limitations |
| Vacuum brazing | Can join complex channel structures and multiple joints in one furnace cycle; suitable for high-volume batch production | Batch-based processing, energy consumption, filler material requirements, and possible post-process cleaning |
| Friction stir welding (FSW) | Solid-state joining, limited distortion under suitable conditions, and dense welds without fusion-related porosity | Best suited to accessible, continuous joints; tooling rigidity and component geometry can restrict application |
| Laser welding | Localized heat input, low distortion potential, non-contact processing, flexible automation, and relatively easy integration into production lines | Sensitive to joint gaps, positioning accuracy, and surface conditions; reflective metals can present process stability challenges |
Laser welding is particularly attractive for applications requiring flexible automation and fast production-line integration. However, process qualification and leak testing remain necessary to confirm suitability for each component design.
Laser Source Solutions for Copper and Dissimilar-Material Welding
Red-Blue Hybrid Laser for Copper Welding
Han’s Laser offers a high-brightness red-blue hybrid laser that combines 450 nm blue light and 1070 nm infrared light in a coaxial optical path. The composite beam places the infrared spot at the center and the blue spot around it.
Blue light generally couples more effectively with copper at room temperature, helping establish a stable molten pool. The higher energy density of infrared light supports deeper penetration. Working together, the two wavelengths can improve process stability and help reduce spatter and unstable keyhole behavior compared with infrared-only welding under suitable conditions.

Copper-to-Stainless-Steel Welding Validation
In a reported test joining 2 mm copper to 2 mm stainless steel in a butt-joint configuration, the comparison used the same infrared laser conditions: 2,000 W, a 14 μm fiber core, and a welding speed of 20 mm/s.
- Infrared-only welding: Visible spatter appeared on the weld surface.
- Red-blue hybrid welding: With 2,000 W infrared power and 1,000 W blue laser power, the weld showed more uniform formation and almost no visible spatter. The examined area after milling showed no obvious defects, and the joint exhibited good bonding.

These observations demonstrate the potential of hybrid laser welding for this specific test configuration. Further metallographic, mechanical, and leak-tightness testing is needed to establish suitability for production cooling components.
Ring Beam and Green Laser Options
Other laser configurations can address different copper welding requirements:
- Ring beam laser: A central beam supports deep penetration, while the surrounding ring beam helps preheat the material and stabilize the molten pool. This approach can help reduce spatter in copper cold-plate applications with approximately 1–2 mm penetration requirements.
- 532 nm green laser: Its wavelength is well suited to copper processing and can support low-heat-input welding of precision, thin-walled components.
Laser source selection should account for material combinations, wall thickness, required penetration, joint geometry, and production cycle time.
In-Process Monitoring for Weld Quality and Traceability
Post-weld inspection and pressure testing are important, but they cannot provide real-time feedback during the welding operation. Han’s Laser integrates two complementary monitoring technologies to identify process anomalies and evaluate weld penetration.
Photoelectric Monitoring for Real-Time Anomaly Alerts
Semiconductor photoelectric sensors collect three types of optical signals during welding:
- Ultraviolet emissions associated with the plasma or metal vapor.
- Reflected laser light.
- Near-infrared radiation from the molten pool.
The monitoring system compares these signals with reference data from qualified welds. When signals fall outside configured limits, it generates an alarm for further review of the affected weld.
This approach helps identify abnormal welding conditions during production. Because signal deviations do not always indicate a defective joint, alarm criteria should be validated against actual weld inspection results.
OCT Monitoring for Penetration Assessment
Optical coherence tomography (OCT) can measure keyhole depth along the weld path in applicable laser deep-penetration welding processes. After calibration against the welding process, depth measurements can help assess penetration and identify locations where insufficient penetration may have occurred.
When monitoring records are linked to workpiece and weld identifiers, manufacturers can retrieve process data for individual joints, supporting traceability and targeted investigation of production anomalies.
OCT data and optical signal monitoring do not independently prove that a cooling component is leak-free. Finished parts must still undergo leak testing and pressure testing according to the product’s acceptance criteria.
Automated Laser Welding Equipment for Liquid Cooling Components
Han’s Laser provides equipment configurations for different liquid cooling components and production requirements.
1.Laser Welding Workstation for Liquid Cooling Manifolds
The laser welding machine supports different penetration requirements and welding methods, including autogenous welding and filler-wire welding where appropriate. Vision guidance identifies manifold nozzle positions and compensates for positioning deviations. Modular fixtures facilitate changeover between product types.

2.Laser Welding Machine for Corrugated Tubes
Designed for corrugated tube assemblies, the machine maintains a tube-to-joint coaxiality of within ±0.05 mm under the specified setup. Replaceable fixtures accommodate different tube specifications, while controlled welding trajectories support consistent joint formation and leak-tightness requirements.

3.Automated Corrugated Tube Assembly and Welding System
This laser welding system integrates material storage, robotic loading and unloading, tube-and-fitting assembly, and laser welding. Dual-channel fixtures support sequential or parallel processing according to the selected production configuration, reducing manual handling between operations.

4.Automatic Liquid Cooling Plate Welding Line
The integrated line connects loading, tube assembly, laser welding, inspection, and unloading. Robotic handling reduces transfers between stations, while storage capacity supports more than one hour of production under the specified configuration. Quality checks can be distributed across the process:
- Before welding: Inspect and position components.
- During welding: Monitor process signals and, where applicable, penetration.
- After welding: Inspect weld appearance and perform required leak or pressure tests.

5.Automatic Laser Welding Machine for Manifold End Caps
For long liquid cooling manifolds, a gantry-based laser welder provides a processing stroke of up to 2.2 m. Quick-change fixtures accommodate different tube cross-sections. After manual loading and clamping, the operator starts the programmed full-seam welding cycle, with suitable parameter selection helping manage heat input and reduce distortion.

Building a More Reliable Liquid Cooling Production Process
As AI server power density increases, liquid cooling manufacturers need joining processes that balance weld quality, production throughput, and traceability. Han’s Laser combines red-blue hybrid, ring beam, or green laser options with automated handling and in-process monitoring to address different material and joint requirements.
A robust production strategy connects three stages: qualified welding parameters, real-time monitoring for process anomalies, and post-weld verification of leak tightness and pressure performance. Together, these measures help manufacturers identify potential defects earlier, investigate production issues more efficiently, and improve process consistency.
Contact Han’s Laser to discuss laser welding and automated production solutions for liquid cooling plates, manifolds, corrugated tubes, and other AI data center cooling components.